Nanostructured nickel film deposition on carbon fibers for improving reinforcement-matrix interface in metal matrix composites

The issues in dispersing any form of carbon in metal matrix is the major problem in the field of metal matrix composites with carbon reinforcement (MMCcr). The low wettability of carbon in molten metals and the difference in density are some of the difficulties to obtain a good dispersion of carbon fibers in the matrix and, as a consequence, an improvement of some critical properties for metals in a wide range of application (mechanical properties, electrical properties, optical properties). For this reason, the aim of this work is to obtain a metallic coated carbon fiber to enhance the interaction between the reinforcement and the matrix. Moreover, also the density of carbon fibers could be adjusted depending on the thickness of the coating. Electroless Nickel-Phosphorus Plating (ENP) is one of the candidate to be a coating technique to improve the interaction between the carbon fibers and the metal matrix. Despite of its versatility in terms of complex geometry of the substrate and homogeneity and adhesion of the coating, the presence of the phosphorus in the alloy could create some problems with the metal matrix such as the formation of metal-phosphorus products that can drastically decrease the mechanical properties of the composite. For this reason, in this work, is presented a new way of Electroless Pure Nickel Plating (EPP) without any introduction of phosphorus in the nickel coating. The dependence of the coating thickness and the density of the coated fibers were studied under different plating parameters (temperature of the plating solution, deposition rate and plating solution composition). All the samples were characterized with SEM and XRD and the thickness, density and homogeneity were compared for all the samples obtained

Alteration of superconductivity of suspended carbon nanotubes by deposition of organic molecules

We have altered the superconductivity of a suspended rope of single walled carbon nanotubes, by coating it with organic polymers. Upon coating, the normal state resistance of the rope changes by less than 20 percent. But superconductivity, which on the bare rope shows up as a substantial resistance decrease below 300 mK, is gradualy suppressed. We correlate this to the suppression of radial breathing modes, measured with Raman Spectroscopy on suspended Single and Double-walled carbon nanotubes. This points to the breathing phonon modes as being responsible for superconductivity in carbon nanotubes

The influence of compact and ordered carbon coating on solid-state behaviors of silicon during electrochemical processes

To address the issues of large volume change and low conductivity of silicon (Si) materials, carbon coatings have been widely employed as surface protection agent and conductive medium to encapsulate the Si materials, which can improve the electrochemical performance of Si-based electrodes. There has been a strong demand to gain a deeper understanding of the impact of efficient carbon coating over the lithiation and delithiation process of Si materials. Here, we report the first observation of the extended two-phase transformation of carbon-coated Si nanoparticles (Si/C) during electrochemical processes. The Si/C nanoparticles were prepared by sintering Si nanoparticles with polyvinylidene chloride precursor. The Si/C electrode underwent a two-phase transition during the first 20 cycles at 0.2 C, but started to engage in solid solution reaction when the ordered compact carbon coating began to crack. Under higher current density conditions, the electrode was also found to be involved in solid solution reaction, which, however, was due to the overwhelming demand of kinetic property rather than the breaking of the carbon coating. In comparison, the Si/C composites prepared with sucrose possessed more disordered and porous carbon structures, and presented solid solution reaction throughout the entire cycling process

A process for the production of a scale-proof and corrosion-resistant coating on graphite and carbon bodies

A process for the production of a corrosion resistant coating on graphite and carbon bodies is described. The carbon or graphite body is coated or impregnated with titanium silicide under the addition of a metal containing wetting agent in a nitrogen free atmosphere, so that a tight coating is formed

Development of Improved Rhenium Coatings for Fluorine Engine Thrust Chambers

Coating trials were undertaken to evaluate the application of rhenium to carbon-carbon composite sheet by plasma spraying. Optimum spray parameters and coating thickness were identified for production of coatings free from continuous defects and with adequate adherence to the substrate. A tungsten underlayer was not beneficial and possibly detracted from coating integrity. Stress calculations indicated that the proposed operating cycle of the rocket engine would not cause spalling of the rhenium coating. Calculations indicated that permeation of gases through the coating would not be significant during the expected life of the thrust chamber. The feasibility of applying rhenium coatings by laser melting was also studied. Poor wetting of the composite surface by the liquid rhenium precluded production of uniform coatings. Borate/carborate fluxes did not improve wetting characteristics

Urea Coating with Activated Carbon Enriched by Microbial Indigenous Can Reduce Endrin Concentration

Endrin residues are still remain in the land field these compounds are no longer used by farmers and have been banned by the government. This residue can stay in the soil longer and persistant. Microbial enrichment is expected to accelerate the degradation of pesticide residues. Microbes stretcher are Bacillus substillis, Heliothrix oregonensis, Catenococcus thiocycli, and Achoromobacter sp obtained from the preliminary research results from soil isolation of idegenus in LIPI Cibinong Microbiology Laboratory. Soil for the planting medium obtained from the village of Karawang, Regency Cilamaya Wetan, Cilamaya District. The experiment was conducted in the field by using lysimeter at the Experiment Jakenan station from July 2013 to December 2013. The objective of the research is to obtain technology of activated carbon-coated urea and biochar which enriched microbial indegenus. The experiment was used randomized block design (RAK) with 3 replications. Plant used are rice. Insecticide residue analysis was carried out in the laboratory in Bogor Balingtan using gas chromatography (GC), with the SNI method 06-6991.1-2004. The purpose of this study knowing the capabilities of urea coating with activated carbon enrichment microbia in reducing the concentration of residues endrin. Results of research urea coated activated carbon from coconut shell are enriched with microbes on paddy field can lower pesticide residues of endrin respectively to 33.6%. This is presumably due to the role of microbes degrading effective as activated carbon as the preferred home. Enrichmentwith microbial indegenuscan improve theeffectivenessof ureacoating biochar andureacoatingactivated carbon coconut shell todecrease concentration endrin

Diamondlike flakes

A carbon coating was vacuum arc deposited on a smooth surface of a target which was simultaneously ion beam sputtered. The bombarding ions have sufficient energy to create diamond bonds. Spalling occurs as the carbon deposit thickens. The resulting diamond like carbon flakes improve thermal, electrical, mechanical, and tribological properties when used in aerospace structures and components

Development of improved coating for advanced carbon-carbon components

Reaction sintered silicon nitride (RSSN) was studied as a substitute coating material on the carbon-carbon material (RCC) presently used as a heat shield on the space shuttle, and on advanced carbon-carbon (ACC), a later development. On RCC, RSSN showed potential in a 538 C (1000 F) screening test in which silicon carbide coated material exhibits its highest oxidation rate; RSSN afforded less protection to ACC because of a larger thermal expansion mismatch. Organosilicon densification and metallic silicon sealing methods were studied as means of further increasing the oxidation resistance of the coating, and some improvement was noted when these methods were employed

Mixed polyvalent-monovalent metal coating for carbon-graphite fibers

An improved coating of gasification catalyst for carbon-graphite fibers is provided comprising a mixture of a polyvalent metal such as calcium and a monovalent metal such as lithium. The addition of lithium provides a lighter coating and a more flexible coating when applied to a coating of a carboxyl containing resin such as polyacrylic acid since it reduces the crosslink density. Furthermore, the presence of lithium provides a glass-like substance during combustion which holds the fiber together resulting in slow, even combustion with much reduced evolution of conductive fragments. The coated fibers are utilized as fiber reinforcement for composites

Thermoplastic coating of carbon fibers

Using a continuous powder coating process, more than 1500 meters of T 300/LaRC-TPI prepreg were produced. Two different types of heating sections in the coating line, namely electrical resistance and convection heating, were utilized. These prepregs were used to fabricate unidirectional composites. During composite fabrication the cure time of the consolidation was varied, and composites samples were produced with and without vacuum. Under these specimens, the effects of the different heating sections and of the variation of the consolidation parameters on mechanical properties and void content were investigated. The void fractions of the various composites were determined from density measurements, and the mechanical properties were measured by tensile testing, short beam shear testing and dynamic mechanical analysis